search account giftcard shopping-cart plus arrow-right checkmark paypal
LED TRAILER LIGHTS KIT TAIL STOP INDICATORS LAMPS & WIRING DB2

Added to Cart

Sold by autoelec

Extended Care

Learn more about .

More deals you may like

LED TRAILER LIGHTS KIT TAIL STOP INDICATORS LAMPS & WIRING DB2

 Marketplace - Sold by autoelec

$30

+ Delivery
Leaves warehouse in 1-2 business days
See delivery information

Qantas Points

You can earn and use Qantas Points at Kogan.com
Qantas Frequent Flyer PointsLogin or Sign up to earn an extra 15 Qantas Points on this purchase
Additional points may be earned during promotional periods. T&Cs apply.

Overview

Marketplace Product

GENUINE LED AUTO LAMPS PLUG AND PLAY TRAILER / CARAVAN , STOP, TAIL & INDICATOR LIGHTS  , 3M TAPE MOUNTING DESIGN & WIRING KIT MODEL P/N DB2

This is a pre-wired Stop/Tail/Indicator package. This kit is ADR compliant and approved and suitable for 12v applications on many of trailers .
NOTE: This kit is NOT supplied with a TRAILER PLUG , so always check the tow vehicle for what plug is on that . Always measure the trailer to make sure that the cable supplied is LONG ENOUGH , if it is too long you can cut the cable but it is more the point if the cable is too short. 



 


100% Water proof plugs and cables
No assembly tools required.
Tinned copper wiring
Save on installation times

INCLUDES
1x DB2LH LED Stop / Tail / Indicator Lamp with 4x High Intensity Red LED’s and 4x High Intensity Amber LED’s in each lamp as well as built in REFLECTOR and PREWIRED with 30CM of 4 core cable
1x DB2RH LED Stop / Tail / Indicator Lamp with 4x High Intensity Red LED’s and 4x High Intensity Amber LED’s in each lamp as well as built in REFLECTOR and PREWIRED with
30CM of 4 core cable

DB2 TAILAMP SPECIFICATIONS
Low Profile ADR approved IP67 100% Water proof
Voltage: 12V
Dimensions: 150mm x 50mm x 25mm  (see below )
Mounting: Surface mount onto flat surface vertically with Indicator at top or horizontally with indicator facing out using prefitted genuine 3m tape and plug through 10mm hole on mounting surface .

 

LIGHT MOUNTING TIPS
For best results from 3M™ Tapes the surfaces should be clean and dry, and provide adequate pressure for ensuring a permanent bond with the surface. Also, ensure the application temperature is sufficient to build adhesion. 3M™ Tapes will build adhesion with time.
Clean :Before applying 3M™ Tapes ensure the surfaces are cleaned with a mixture of soapy water. Exceptions to the general procedure, which may require additional surface preparation include:Heavy Oils where
A degreaser or solvent-based cleaner is required to remove heavy oil or grease from the surface. Note here that this process should begin only after cleaning with the mixture of soap and water.
Abrasion This process should begin only after cleaning the surface with the soap and water mixture – abrasing a surface can remove heavy dirt or oxidation and increases surface area to improve adhesion.
The ideal temperature for application is between 70ºF to 100ºF (21ºC to 38ºC).Note:here that the initial tape application to surfaces at temperatures below the suggested minimum temperatures is not recommended, because the adhesive becomes too firm. However, if the tape is applied properly, the low temperature bonding is generally satisfactory. To obtain the best performance with all 3M™ VHB™ Tapes, ensure that the surfaces are dry and free of condensed moisture.After application, the bond strength increases, as the adhesive flows onto the surface. At room temperature, the adhesion becomes stronger – 50% (approx.) after 20 minutes, 90% after 24 hours and 100% after 72 hours.

CONNECTION FOR 5 PIN
2  left hand turn -  yellow
3  earth  -  white                            
5  right hand turn -  green
6  stop  -  red
7  tail, clearance, side markers  -  brown

CONNECTION FOR 7 PIN
1  left hand turn -  yellow     
2  reverse  -  black                                         
3  earth  -  white                                                                            
4   right hand turn -  green                                        
5  electric brakes  -  blue
6  stop  -  red
7  tail, clearance, side markers  -  brown

CONNECTION FOR 6 PIN
1  tail, clearance  -  brown                                  
2  left hand turn  -  yellow 
3  right hand turn -  green
4  stop -  red
5  electric brakes  -  blue
6  earth  -  white

Create your free Kogan.com account

Create your free Kogan.com account

Already have an account? Log In

By clicking Create Account (or signing in with Facebook, Google or Paypal), you agree to the Kogan.com Terms & Conditions and Privacy Policy and to receiving marketing communications from Kogan.com. Remember, you can unsubscribe at any time.